SKIRTING PACKAGE - FOR SMOOTH,NON PORUS RV SIDING
PRICING ---- 34"INCH TALL AT--- $6.00 PER FT. PLUS SHIPPING
VELCRO SYSTEM FOR RIBBED,DIMMPLED OR ROUGH SIDING
WE NOW HAVE THE FRONT 5TH WHEEL SKIRTS
ALL SIZES AVAILABLE
34"INCH - 8 OUNCE - NON WOVEN GEOSYNTHETIC FABRIC - ANY LENGTH
BLACK IN COLOR- 160 LB PER INCH TEAR STRENGTH
PLEATED TOP EDGE - GROMMETED EVERY 18"INCHES
2-1/2" INCH TRIPPLED RIBBED INCH SUCTION CUP SYSTEM WITH HOOKS
SKIRT TO GROUND - PVC- HOLD DOWN SYSTEM
ADJUSTABLE TO UNEVEN GROUND
COMPLETE KIT- (except pvc pipe) CLIPS INCLUDED
EASY TO INSTALL
NO HOLES- NO SNAPS - OR RV DAMAGE
SAMPLE KIT AVAILABLE - $17 REFUNDABLE UPON PURCHASE OF KIT
2'ft x 34"in panel, cups, pvc pipe with the clips, includes shipping
MEASURE THE LENGTH - (not including the 5th wheel high hitch area)
MEASURE THE WIDTH
MEASURE THE DISTANCE ANY SLIDES EXTEND
SEPERATE PANELS SHOULD INCLUDE A 3"INCH OVERLAP
TOTAL FOR LENGTH OF SKIRTING
CHECK FOR TYPE OF SYSTEM- CUP-REQUIRES SMOOTH NON-PORUS SIDING
VELCRO FOR RIBBED OR ROUGH SIDING
CHECK FOR ANY SPECIAL PANELS YOUR RV MAY REQUIRE-(slides and slide ends)
Please email us at firstname.lastname@example.org, you can click on the link above or call 541-521-7202 with the ordering information. We like to know the year,type and model , also your location for shipping charges. Average shipping in the u.s. is around $50.00
ANY QUESTIONS? JUST ASK .
WE ARE VERY PROUD OF OUR PRODUCT AND WORKMANSHIP
WE OFFER A GREAT PRODUCT AT A FAIR PRICE
YOU CAN ALSO REPLACE YOUR VINIAL SNAP SYSTEM WITH OUR GEOSYNTHETIC SYSTEM--- YOU JUST ADD THE SNAPS TO OUR SKIRTING
REVIEWS FROM SKIRTING CUSTOMERS
Mark from oaklahoma wrote: - The skirting works perfectly. We had a VERY strong wind storm the very night we installed it and it held tight!
Product worked great. Just got back from my hunting trip where temps dropped into the teens and water tank and lines did not freeze. Didnt even have to use heater I bought for underneath the trailer. I do have heated floors so I am sure that helped but they were still always cold and the tank always froze no matter what. Thank you again for everything!
I finally got around to getting the kilt on my trailer. It is so windy where I am in a storm. I used the grommet kit to put grommets in each at the bottom edge of each corner of the trailer and slide, and a few along the long ends and I tent pegged the bottom edge down. I really like the finished product, it is very sharp compared to the others I see in the campground.
I should have done this much earlier in the year but it is done and I am very pleased with it.
Thanks very much. paul
hello , i am in need of a price for a skirt that will fit these measurements. I ordered off of you a couple months ago and my customer was extremely happy. You put out a wonderful product. please let us know what the cost will be. Thanks and have a wonderful day .
NO HOLES TO DRILL - NO RV DAMAGE - EASY INSTALLATION - REDUCED ENERGY COSTS ADDS STORAGE UNDER RV - LOW COST - PVC HOLD DOWN SYSTEM - ADJUSTABLE
ABOUT SLIDE AREA'S
SLIDES AND .WHEEL WELL AREAS ARE OFTEN HIGHER THEN THE REST OF YOUR RV. THE SKIRTING COMES IN ONE PIECE APROX. 34"IN.TALL AND YOU CAN BE CUT AND RAISED IN THESE AREAS . (THE KIT INCLUDES EVERYTHING YOU NEED TO RESECURE THE CUT AREA) WE ALSO CAN MAKE SKIRTING TO ANY SPECIFACATIONS YOU REQUIRE
IF YOU HAVE SLIDES, SOME SLIDE ENDS (THE PART THAT ACTUALLY SLIDES INTO THE RV) ARE OFTEN HIGHER THEN THEN THE REST OF THE SLIDE. THESE AREAS SHOULD BE A SEPERATE PANEL.IF YOU NEED A TALLER PANEL HERE WE CAN MAKE THOSE UP FOR YOU IN ANY SIZE YOU NEED THEM. THE SEPERATE PANELS ARE HELD TOGEATHER WITH THE PVC HOLD DOWN SYSTEM AT THE BOTTOM .
SKIRTING TO GROUND HOLD DOWN SYSTEM
THE PVC HOLD DOWN SYSTEM CONSISTS OF 1/2"INCH PVC PIPE WHICH YOU BUY LOCALLY, IN EXTRA HIGH WIND AREAS YOU CAN USE 3/4 IN. PVC PIPE, THE FABRIC CLIPS THAT HOLD THE SKIRT TO THE PVC PIPE COME WITH YOUR KIT. THE SYSTEM WORKS WELL AND IS INEXPENSIVE. MAKES A COMPLETE SYSTEM, AROUND CORNERS AND SLIDES. EASY TO DISMANTEL AND HAUL.
MADE TO YOUR REQUIRMENTS
WE MAKE YOUR KIT TO FIT YOUR NEEDS, THIS SYSTEM IS VERY EASY TO INSTALL AND ADAPTABLE TO MOST ANY AREA ON YOUR RV. WE DO MOTORHOMES AS WELL, WE CAN MAKE SPECIAL PANELS FOR YOUR WHEEL-WELLS, GRILLS, SLIDES, PORCHES, FIFTHWHEEL HITCH AREA, WHATEVER YOU REQUIRE.
GENERAL SYSTEM SET-UP
COMPLETE INSTRUCTIONS AND TIPS INCLUDED IN KIT
STEP 1. Level your rv.. make sure area for cups or velcro is clean and dry. remember, slides, and wheelwells are often higher then the rest of your rv,, these area's will be a seperate panel, raised to cover properly
TIP: ALLOW SEPERATE PANELS TO OVERLAP EACH OTHER APROX. 3"INCHES, THE PVC HOLD DOWN SYSTEM WILL HOLD THEM TOGEATHER
TIP: YOU CAN BE CREATIVE WITH OUR SKIRTING- IF THE SKIRTING IS WHERE YOU WANT IT BUT THE CUP IS IN A BAD SPOT, YOU CAN EXTEND THE CUP UP FROM THE SKIRTING USING THE ENCLOSED FELT STICKS... CLIPS ARE ALSO INCLUDED TO CLIP THE TOPS OF PANELS TOGEATHER, OR REATTACH TRIMMED STEP MATERIAL BACK TO THE CROSS BAR. ECT..
Start your install at one of these joints. The fewer joints the better. Take your time with the set-up. If you wish to trim your skirtings height now is a good time.
STEP 3: INSTALLING THE CUPS: First put the hook on the cup into the grommet on skirting, then place cup onto surface and push on with the button on the cup. Allow cups to mold to surface, recheck occasionially, if a cup comes loose,, push it back on
TIP: SOMETIMES YOU NEED TO PUSH THE CUPS ON MORE THEN ONCE. THE REPOSIONABLE ADHESIVE WORKS WELL ON CUPS, SIMPLY RUB ON CUP AND INSTALL. USE THIS ONLY IF NEEDED. WHEN CUPS ARE TO BE REUSED THEY NEED TO BE CLEANED AND ALLOW TO SIT AT ROOM TEMPTURE FOR AN HOUR OR SO TO REGAIN THERE SHAPE.
Repeat step on next cup, pull the skirt snug with the each cup as you go along assuring a nice fit. If you make a cut for seperate panel or need a grommet where there isn't one a grommet kit is supplied for this with your kit. velcro also works well in these area's and is simpler to install,
TIP: WHEN PUTTING VELCRO ON YOUR SKIRTING USE THE SUPPLIED LOCKTITE SPRAY ADHESIVE ON THE SKIRTING AND VELCRO BEFORE JOINING THE TWO. DO NOT USE ON THE RV.. IT IS TO STRENGTH THE VELCRO-SKIRT BOND..
Continue on around your rv paying close attention to keeping it straight and wrinkle free, take your time. When doing a slide a seperate panel may be needed on the slide end that actually slides into the rv. This area is commonly higher then the rest of the slide, this is a good area to use velcro to hold the skirt on. Use the clips supplied for the sharp edge of your slide, clips should slide over the gasket and hold the skirt well.
TIP: IF CLIP IS TO LOOSE USE A SCRAP PIECE OF SKIRTING INTO THE CLIP AND
WRAP INTO THE CLIP SO IF FITS TIGHT, I USE 2 CLIPS PER END OF SLIDE. ONE HIGH, ONE LOW.
STEP 4: YOUR PVC SKIRT TO GROUND HOLD DOWN SYSTEM: You buy the schedual 40. 1/2" inch pvc pipe locally and use the enclosed c-clips to hold the skirt to the pvc pipe, get 90' degree elbows as well as this is a complete system. Do not glue the pipe togeather so you can dismantel later for travel. Wrap fabric around pipe and place clamp on. As you continue on, pull fabric snug to avoid wrinkles. To remove clamp grap fabric right in front of clamp and pull up.
TIP: NUMBER EACH PIPE FOR EASY REINSTALLATION LATER. KEEP PVC PIPE SHORTER ENOUGH FOR YOU TO HAUL IN YOUR RV
IF HIGH WINDS ARE AN ISSUE YOU CAN PUT A WEIGHT ON THE INSIDE OF EACH CORNER OF YOUR SKIRT.
IF EXTREME COLD IS AN ISSUE, PUT A HEAT BULB OR SUCH TO KEEP PIPES FROM FREEZING.
TIPS: DOORS, STEPS , BUMPERS, ECT. CAN EASILY BE TRIMMED AND REATTACHED WITH THE VELCRO, OR A GROMMET AND CUP, YOU CAN BE CREATIVE AS YOU WISH, KEEEP IT SIMPLE.
THE CUPS CAN GENERALLY BE LEFT IN PLACE WHEN YOU TRAVEL, ESPECIALLY WHEN USING THE REPOSIONABLE ADHESIVE ON THE CUPS, IN EXTREME CASES OF CUP ISSUES YOU CAN USE THE LOCTITE ADHESIVE TO
ATTACH TO YOUR RV, BUT THEY WONT BE EASILY REMOVABLE.
< New text box >>
YOUR SKIRTING KIT INCLUDES
THE SKIRTING- ITS PLEATED ON THE TOP EDGE AND GROMMETED WITH 3/8 INCH BRASS GROMMETS EVERY 18 INCHES,
COMES IN APROX A 34" INCH HEIGHT. BLACK IN COLOR.
2 1/2 INCH SUCTIONS CUPS WITH HOOKS, ENOUGH FOR EVERY GROMMET PLUS A FEW
. ENOUGH FABRIC CLIPS FOR THE PVC HOLD DOWN SYSTEM, YOU BUY THE 1/2'INCH OR 3/4"INCH SCHEDUAL 40 PVC PIPE LOCALLY WE SUPPLY THE CLIPS.
. ALSO SOME INDUSTRIAL STRENGTH VELCRO INCASE YOU NEED TO MAKE A DOOR, OR ROUND A CORNER AND WANT SOME EXTRA HOLDING POWER, ECT.
FABRIC GLUE FOR EXTRA HOLDING POWER OF THE VELCRO TO THE FABRIC.
REPOSIONABLE ADHESIVE INCASE YOU HAVE A FEW CUPS IN A INPERFECT AREA OR JUST WANT THE EXTRA HOLD, IT SUPPLIES A TACKY COAT SO THE CUPS WONT LET GO AND WONT HURT YOUR PAINT.
MINI CLIPS FOR SECURING THE TOP OF ANY SEPERATE PANELS IF YOU HAVE THEM
MINI CLAMPS FOR SECURING THE STEP AREA BACK TO THE TENSION BAR
MINI PADS FOR CLEANING THE AREA OF SKIRT PLACEMENT
GROMMET KIT FOR RESECURING ANY CUT AREA'S
FUZZY WIRE EXTENDERS FOR RAISING A CUP ABOVE THE SKIRTING TO AVOID AN OBSTRUCTION
INSTRUCTIONS AND TIPS
IF YOUR NOT SURE PLEASE ORDER THE SAMPLE KIT
WE EXCEPT PAYMENT TRU PAYPAL ONLY - YOU DO NOT NEED A PAYPAL ACCOUNT TO USE THIS SERVICE -- AFTER PAYING AT OUR PAYPAL SITE YOU CAN PRINT A RECIEPT AND UPON SHIPPING YOU WILL RECIEVE THE TRACKING NUMBER. SHIPPING WEIGHT IS APROX. 26 LBS. DEPENDING ON LENGTH OF SKIRT.
WHEN CALLING IF YOU GET THE MESSAGE MACHINE , 541-521-7202 , PLEASE LEAVE YOUR PHONE NUMBER, OR USE OUR MESSAGE US FORM OR EMAIL AT email@example.com
THE SKIRTING IS A GEOSYNTHETIC NON-WOVEN FABRIC, VERY STRONG- 160LB TEAR STRENGTH-8oz.- THE CUPS ARE OF SURGICIAL GRADE, TRIPPLE RIDGED, WITH HOOKS AND HAVE GREAT GRIPPING POWER IN COLD AND WET-
WE DO OFFER A SAMPLE KIT COMPLETE WITH A 2'FT SECTION OF PLEATED FABRIC-SUCTION CUPS- WITH A SECTION OF PVC PIPE HELD ON WITH THE CLIPS THAT ARE PROVIDED WITH YOUR KIT. I CHARGE $17 DOLLARS TO COVER SHIPPING,MATERIAL AND HANDELING REFUNDABLE UPON SKIRTING PACKAGE PURCHASE